adminHigh pass rate 200-155 dumps practice questions and answers, real Cisco 200-155 dumps exam training materials online free update, download one of the many PDF readers that are available for free. https://www.leads4pass.com/200-155.html Cisco CCNA Data Center products is considered a very important qualification, and the professionals certified by them are highly valued in all organizations.
QUESTION 1
An engineer is configuring a new MDS switch. The switch is powered on, the customer connects to the console, and the initial setup script is started.
Which two items can be configured during this setup process?
A. default port-channel mode
B. default port VSAN membership
C. default switch port interface state
D. default zone mode
E. default storage VDC
Correct Answer: CD
QUESTION 2
Which option describes a difference between EIGRP for IPv4 and IPv6?
A. Only EIGRP for IPv6 advertises all connected networks.
B. Only EIGRP for IPv6 requires a router ID to be configured under the routing process-
C. AS numbers are configured in EIGRP but not in EIGRPv3.
D. Only EIGRP for IPv6 is enabled in the global configuration mode.
Answer : B
Explanation:
Router ID – Both EIGRP for IPv4 and EIGRP for IPv6 use a 32-bit number for the EIGRP router ID. The 32-bit router ID is represented in dotted-decimal notation and is commonly referred to as an IPv4 address. If the EIGRP for IPv6 router has not been configured with an IPv4 address, the eigrp router-id command must be used to configure a 32-bit router ID. The process for determining the router ID is the same for both EIGRP for IPv4 and IPv6.
QUESTION 3
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the 200-155 Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer : C
QUESTION 4
Which option describes what a switch does after it items that a host has connected to a switch port?
A. Flood the frame only on all of its trunk ports.
B. Create a MAC to port mapping entry in MAC table.
C. Flood the frame only on all of its access ports.
D. Discard the frame.
Correct Answer: C
QUESTION 5
What is the maximum working distance of a 1000BASE-ZE SFP transceiver when ordinary single mode fiber?
A. up to 70 kilometers
B. up to 40 kilometers
C. up to 550 meters
D. up to 10 kilometers
Correct Answer: D
QUESTION 6
Which command set creates an access control list on a Cisco Nexus switch to deny only FTP traffic from any source to destination host 10.10.10.10?
A. N5K-A(config)# Ip access-list 101
N5K-A(config-acl)# deny judp any host 10.10.1.110. eq 21 N5K-A(config-acl)# permit ip any any
B. N5K-A(config)# Ip access-list 101
N5K-A(config-acl)# deny judp any host 10.10.1.110. eq ftp
C. N5K-A(config)# deny tcp any host 10.10.1.110. eq ftp N5K-A(config)# access-list 101deny Ip any any
D. N5K-A(config)# Ip access-list 101
N5K-A(config-acl)# deny tcp any host 10.10.1.110. eq 21 N5K-A(config-acl)# permit Ip any any
Correct Answer: D
QUESTION 7
Which two circumstances can cause collision domain issues on VLAN domain? (Choose two.)
A. duplex mismatches on Ethernet segments in the same VLAN
B. multiple errors on switchport interfaces
C. congestion on the switch inband path
D. a failing NIC in an end device
E. an overloaded shared segment
Answer : A,C
QUESTION 8
What is a difference between TACACS+ and RADIUS in AAA?
A. Only TACACS+ allows for separate authentication.
B. Only RADIUS encrypts the entire access-request packet.
C. Only RADIUS uses TCP.
D. Only TACACS+ couples authentication and authorization.
Correct Answer: A
QUESTION 9
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three)
A. configure static frame relay map entries for each subinterface network.
B. remove the ip address from the physical interface
C. create the virtual interfaces with the interface command
D. configure each subinterface with its own IP address
E. disable split horizon to prevent routing loops between the subinterface networks
F. encapsulate the physical interface with multipoint PPP
Correct Answer: BCD
QUESTION 10
Which statement about named ACLs is true?
A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.
Answer : A
Explanation:
Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), 200-155 we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.
Read more: https://www.leads4pass.com/200-155.html
Watch the video to learn more:
https://youtu.be/MHDYkPVUMBQ