adminThe best Cisco 300-115 dumps exam training materials and study guide, latest https://www.leads4pass.com/300-115.html dumps exam practice questions and answers. 100% success and guarantee to pass 300-115 exam test quickly and easily at first attempt.
QUESTION 1
For client server failover purposes, the application server team has indicated that they must not have the standard 30 second delay before their switchport enters a forwarding state. For their disaster recovery feature to operate successfully, they require the switchport to enter a forwarding state immediately. Which spanningtree feature satisfies this requirement?
A. Rapid Spanning-Tree
B. Spanning-Tree Timers
C. Spanning-Tree FastPort
D. Spanning-Tree PortFast
E. Spanning-Tree Fast Forward
Correct Answer: D
Explanation:
In order to allow immediate transition of the port into forwarding state, enable the STP PortFast feature. PortFast immediately transitions the port into STP forwarding mode upon linkup. The port still participates in STP. So if the port is to be a part of the loop, the port eventually transitions into STP blocking mode.
Example configuration:
Switch-C# configure terminal
Switch-C(config)# interface range fa0/3 – 24
Switch-C(config-if-range)# spanning-tree portfast
QUESTION 2
What does the command vlan dot1q tag native accomplish when configured under global configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.
Correct Answer: D
Explanation:
The “vlan dot1q tag native” will tag all untagged frames, including control 300-115 traffic, with the defined native VLAN.
QUESTION 3
When you design a switched network using VTPv2, how many VLANs can be used to carry user traffic?
A. 1000
B. 1001
C. 1024
D. 2048
E. 4095
F. 4096
Correct Answer: B
Explanation:
VTP versions 1 and 2 Supports normal VLAN numbers (1-1001). Only VTP version 3 supports extended VLANs (1-4095).
QUESTION 4
A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?
A. IRDP
B. LLDP
C. NDP
D. LLTD
Correct Answer: B
Explanation:
The Link Layer Discovery Protocol (LLDP) is a vendor-neutral link layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on an IEEE 802 local area network, principally wired Ethernet. LLDP performs functions similar to several proprietary protocols, such as the Cisco 300-115 Discovery Protocol (CDP).
QUESTION 5
A manager tells the network engineer to permit only certain VLANs across a specific trunk interface. Which option can be configured to accomplish this?
A. allowed VLAN list
B. VTP pruning
C. VACL
D. L2P tunneling
Correct Answer: A
Explanation:
When a trunk link is established, all of the configured VLANs are allowed to send and receive traffic across the link. VLANs 1 through 1005 are allowed on each trunk by default. However, VLAN traffic can be removed from the allowed list. This keeps traffic from the VLANs from passing over the trunk link.
Note: The allowed VLAN list on both the ends of the trunk link should be the same. For Integrated Cisco IOS Software based switches, perform these steps:
1.To restrict the traffic that a trunk carries, issue the switchport trunk vlan-list interface configuration command.
This removes specific VLANs from the allowed list.
QUESTION 6
Which statement about the use of SDM templates in a Cisco switch is true?
A. SDM templates are used to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hosts in one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users to manage the flow of traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.
Correct Answer: A
Explanation:
You can use SDM templates to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network. You can select a template to provide maximum system usage for some functions; for example, use the default template to balance resources, and use access template to obtain maximum ACL usage. To allocate https://www.leads4pass.com/300-115.html hardware resources for different usages, the switch SDM templates prioritize system resources to optimize support for certain features.
Read more: http://www.ciscoexampdf.com/latest-cisco-300-115-exam/
Watch the video to learn more:
https://youtu.be/wyXFLuYtFpI